MINI MASTER SIGHT ADJUSTMENT

darticus · January-20-19 08:01

HELP! Needed! How do you adjust these sights. The screw in the back sight must be up and down but what about right and left? Anyone do this? Thanks Ron

OV-1D · January-20-19 14:01

Oh my but just a guess maybe left and right sighting with forward blade . Need target and a sandbag to get it just so-so .

Rick_Jorgenson · January-21-19 08:01

Are they the adjustable sights?

If so, The up-down adjustment for the rear sight is...

Loosen the top Allen screw, the sight will drift forward to lower or backward to raise.

Hope this helps.

Photo shows the difference of adjustable 8mm tall or non adj. 5.5mm tall

darticus · January-22-19 16:01

There is no rear allen screw. It looks like the rear is a screw for up and down. Maybe the front is a hit right and left. Tell me whats right before I try to hit things. This is a Mini Master conversion and adjustable sites. Thanks Ron or email [email protected] SEE PICS

Canoeal · January-22-19 17:01

To get to the allen screw to adjust the drift, you need to take the top half of the adjustable sight off the screw is under it.

Uncle_Lee · January-23-19 04:01

Quote from: Canoeal on January-22-19 17:01
To get to the allen screw to adjust the drift, you need to take the top half of the adjustable sight off the screw is under it.

Thanks, I didn't know that.
Now I can scoot it sideways.

darticus · January-23-19 06:01

Quote from: uncle_lee on January-23-19 04:01
Quote from: Canoeal on January-22-19 17:01
To get to the allen screw to adjust the drift, you need to take the top half of the adjustable sight off the screw is under it.

Thanks, I didn't know that.
Now I can scoot it sideways.

I am stupid to this. You are talking about the rear sight. What is drift? This rear sight adjusts up and down, RIGHT? How do you adjust side to side, have patience. Thanks, I really need better explanation. How does the front and back dovetail sight move? Muzzle pointed away does it move right to left to take out or left to right? Thanks again Ron

darticus · January-23-19 10:01

I took the rear sight apart and it is an adjustment only for up and down with the screw no Allen screw below. I guess someone could move the sight right or left in the dove tail for left or right but I think right and left is done by moving the front dovetail sight right or left. I don't want to hit on the front dovetail until I know from which side to hit it as it might be tapered on one side to exit By the other. Here are some pics. Thanks a lot Ron

Uncle_Lee · January-23-19 14:01

Keep trying Ron.
After 15 posts, it gets easier.

Canoeal · January-23-19 14:01

I will have to get down as far as my basement to look at the rear sights I took off. I replaced mine with fixed sights, I had two sets of rear adjustables before switching. I could keep the screws tight. Sights kept coming loose. My BW has had several incarnations; adjustable sights, fixed sights/w Venom lasers, now fixed sights, and two different grips. Got it right for now, until the trit sights become available...

darticus · January-23-19 17:01

Got the front site to move to the left and right to the outer edge on each side but not out. Left it in the middle. I made a little jig to hold the barrel and press with a vise. Even with a vice it was tough. I guess if I kept pushing it would come out from one side or the other. Would like to know which side it should come out from. It did get flush so you would think it would come out of either side.Like to see some of the upgrade sights you guys are using. Post some images. Thanks again Ron

Canoeal · January-24-19 12:01

Three dot sight are the upgrade...at least for now. They are working on a trit sight for the BW, probably somewhat like the Pug sights , but I have not heard they are ready yet. The Fixed sight versions of three dots are better than most other NAA's...other than the Pug.

OV-1D · January-24-19 15:01

Quote from: darticus on January-23-19 17:01
Got the front site to move to the left and right to the outer edge on each side but not out. Left it in the middle. I made a little jig to hold the barrel and press with a vise. Even with a vice it was tough. I guess if I kept pushing it would come out from one side or the other. Would like to know which side it should come out from. It did get flush so you would think it would come out of either side.Like to see some of the upgrade sights you guys are using. Post some images. Thanks again Ron

Oh yes we need pictures for sure ,,, HURRY .